Monolayer 1T and 1T′ MoSO as Promising Electrocatalyst for Hydrogen Evolution based on First Principle Calculations

Molybdenum disulfide (MoS₂) has been regarded as one of the most promising candidates for replacing Pt group noble metals as an efficient electrocatalyst to enhance the hydrogen evolution reaction (HER) in consideration of its relatively high earth abundance. Recent studies show that the catalytic efficiency of MoS₂ for HER can be promoted by the presence of 1T-phase MoS₂. It is hard to precisely control the formation of 1T-MoS₂, however, due to its metastability relative to 2H-MoS₂. Elevating the stability of 1T phase allotrope is therefore of great importance and could be realized by replacing divalent S with monovalent elements or groups according to crystal field theory, which has been demonstrated through our first-principles density functional theory (DFT) calculation results. Differential Gibbs free energy analysis for hydrogen adsorption (ΔG_H*) suggest that 1T and 1T′ MoSO (O doped MoS₂) might be taken as potential candidate catalysts for HER process with better performance than 1T and 1T′ MoS₂. We also propose a probable approach to synthesize 1T and 1T′ MoSO under oxidation circumstance environment of graphene oxide.     

Influence of Carbon Nanotubes on Phase Composition,Thermal and Post-Heating Behavior of Cementitious Composites

This paper experimentally investigates the influence of carbon nanotubes (CNTs) on phase composition, microstructure deterioration, thermal behavior, and residual mechanical strengths of cementitious composites exposed to elevated temperatures. Cement mortars with small dosages of CNTs, 0.05% and 0.2% by weight of cement, were prepared and then heated at 25 °C, 150 °C, 200 °C, 450 °C, and 600 °C for two hours before being tested. The results show positive impact of the CNTs on the hydration process of cement mortar at room temperature and at higher temperatures up to 200 °C. Decomposition of the hydration products is obvious at 450 °C, whereas sever deterioration in the microstructure occurs at 600 °C. The nano reinforcement and bridging effect of the CNTs are obvious up to 450 °C. Thermal behavior characterization shows that CNTs incorporation enhances the thermal conductivity of the unheated and heat-treated mortar specimens. The decomposition of the hydration products needs more heat in the presence of CNTs. Finally, presence of CNTs significantly enhances the residual compressive and flexural strengths of heated mortar specimens for all studied temperatures.     

Phase‐Junction Electrocatalysts towards Enhanced Hydrogen Evolution Reaction in Alkaline Media

To ensure sustainable hydrogen production by water electrolysis, robust, earth‐abundant, and high‐efficient electrocatalysts are required. Constructing a hybrid system could lead to further improvement in electrocatalytic activity. Interface engineering in composite catalysts is thus critical to determine the performance, and the phase‐junction interface should improve the catalytic activity. Here, we show that nickel diphosphide phase junction (c‐NiP₂/m‐NiP₂) is an effective electrocatalyst for hydrogen production in alkaline media. The overpotential (at 10 mA cm^?2) for NiP₂‐650 (c/m) in alkaline media could be significantly reduced by 26 % and 96 % compared with c‐NiP₂ and m‐NiP₂, respectively. The enhancement of catalytic activity should be attributed to the strong water dissociation ability and the rearrangement of electrons around the phase junction, which markedly improved the Volmer step and benefited the reduction process of adsorbed protons.     

The preparation of ionic liquid based iron phosphate/CNTs composite via microwave radiation for hydrogen evolution reaction and oxygen evolution reaction

Water electrolysis is a promising method for hydrogen production, so the preparation of low-cost and efficient electrocatalysts with a quick and simple procedure is crucial. Herein, iron phosphate (Fe₇(PO₄)₆) was prepared via microwave radiation using ionic liquid (IL) as iron and phosphorus dual-source. This method is simple and rapid, and the product can be directly used as electrocatalysts without further treatment. The experimental results show that the IL can influence the morphology and electrocatalytic performance. Moreover, the addition of carbon nanotubes (CNTs) is favorable for formation of iron phosphate nanoparticles to improve the catalytic activities. As hydrogen evolution reaction (HER) catalyst, this iron phosphate/CNTs exhibits an onset overpotential of 120 mV, Tafel slope of 32.9 mV dec^-1, and current densities of 10 mA cm⁻² at overpotential of 185 mV. Then, it obtains a good activity for oxygen evolution reaction (OER) with a low onset potential of 1.48 V, Tafel slope of 73.3 mV dec^-1, and it only needs an overpotential of 300 mV to drive the 10 mA cm⁻². This bifunctional catalyst also shows good durability for HER and OER. This microwave-assisted method provides an outstanding strategy to prepare iron phosphate in a simple and fast process with good catalytic performance for water splitting.     

金属性二维过渡金属硫化物的溶剂热合成及电催化析氢性能

采用溶剂热法制备了多种二维过渡金属硫化物(TMDCs), 在合成过程中通过调控反应前驱体的滴加速率来控制所得TMDCs的形貌和结构. 然后采用高温热处理来提高TMDCs的结晶性, 从而提升了其电催化活性. 在酸性电解液中进行电催化析氢性能测试. 结果表明, “花状”结构的金属性二维二硫化铌(NbS₂)具有最佳的催化活性和稳定性, 在电流密度为10 mA/cm²时, 其过电位仅为146 mV, 持续工作24 h后电流密度几乎不衰减. 研究发现, 可充分暴露面内活性位点的“花状”结构以及高温处理后材料导电性的提高是二维NbS₂具有优异电催化性能的主要因素.     

纳米二硫化钼的掺杂及催化电解水产氢的研究进展

电催化水分解制氢是可以形成闭环的生产过程, 起始原料与副产物均为水、 过程清洁无污染, 是极具希望的产氢策略. 目前制约其发展的瓶颈之一是价格昂贵的Pt基贵金属催化剂. 为推动电催化分解水制氢的普及, 亟待开发低成本非贵金属催化剂. 在众多备选非贵金属催化材料中, 纳米层状结构二硫化钼(MoS₂)因催化效果可期、 价格低而获得了广泛关注. 然而, 通常条件下易于获得的层状结构2H相MoS₂大面积的基面部分显示惰性, 仅在片层边缘处存在少量活性位点, 且导电性较差, 因而尚不能替代Pt基催化剂, 而如何增加其活性位点数量和提高其导电性成为亟待解决的问题; 另一方面, 1T相MoS₂虽然活性高、 导电性好, 但却存在制备困难及稳定性差的问题. 鉴于此, 研究者通过对纳米MoS₂进行掺杂改性实现了其活性与稳定性的有效提升. 本文对非贵金属纳米MoS₂催化剂掺杂改性的方法、 机理及其电催化水解制氢性能的相关研究进行了总结与讨论. 作为典型的非贵金属电解水析氢催化剂, MoS₂具有巨大发展潜力, 本文能够对相关非贵金属催化剂的研发提供有益的参考.     

Comparison of the Structural Evolution of β Polypropylene during the Sequential and Simultaneous Biaxial Stretching Process

In this work, the lamellar structural evolution and microvoids variations of β polypropylene(β-PP) during the processing of two different stretching methods, sequential biaxial stretching and simultaneous biaxial stretching, were investigated in detail. It was found that different stretching methods led to significantly different lamellae deformation modes, and the microporous membranes obtained from the simultaneous biaxial stretching exhibited better mechanical properties. For the sequential biaxial stretching, abundant coarse fibers originated from the tight accumulation of the lamellae parallel to the longitudinal stretching direction, whereas the lamellae perpendicular to the stretching direction were easily deformed and separated. Those coarse fibers were difficult to be separated to form micropores during the subsequent transverse stretching process, resulting in a poor micropores distribution. However, for the simultaneous biaxial stretching, the β crystal had the same deformation mode, that is, the lamellae distributed in different directions were all destroyed, forming abundant microvoids and little coarse fibers.     

可控表面磷原子修饰提升超细W2C纳米颗粒电解水析氢反应性能

研究高活性和稳定性的非贵金属基析氢催化剂对解决当前能源危机和环境污染问题具有重要意义.碳化钨具有与贵金属Pt类似的d带电子结构,因而成为一类新兴的非贵金属析氢催化剂,受到广泛关注.磷掺杂是提高催化剂析氢活性的有效方法之一,然而目前最常见的构筑磷掺杂方法是使用多金属氧酸盐(POMs,如H3PW12O40),其固定的W/P原子比导致W2C中的掺杂浓度难以调控,并且磷掺杂主要是进入碳载体而不是碳化物本身,从而导致无法明确杂原子对其电催化析氢活性的贡献.本文采用植酸(PA)为磷源设计合成了可控磷掺杂W2C纳米颗粒,并探讨了催化剂组分、杂原子掺杂位置与析氢性能之间的关系.深入研究了磷掺杂碳化钨(WCP)的化学结构和析氢活性.与原始的W2C催化剂相比,WCP具有更高的本征活性、更快的电子转移速率和更多的活性位数量,并且在酸性和碱性条件下均表现出较好的析氢性能.特别是过电位为-200 mV时,WCP催化剂的本征活性在酸性和碱性条件下分别为0.07和0.56 H2 s-1,高出纯W2C(0.01和0.05 H2 S-1)数倍.同时,在电流密度为-10 mA cm-2时,优化后的WCP催化剂在酸性和碱性条件下的析氢过电位分别降低了96和88 mV.XPS及EDS元素分析结果表明,随磷源添加量增加,磷掺杂从碳化钨表面逐渐向内部扩散,进一步说明磷取代位置与析氢活性之间的构效关系,高浓度的表面磷取代可以加速质子捕获过程,从而显著提高其析氢活性,而过量的内部磷取代会破坏W2C结构,降低电子转移速率,从而导致析氢性能下降.利用密度泛函理论计算深入研究了WCP具有较好析氢性能的原因,与内部磷取代相比,表面磷取代会使碳化钨表现出更合适的氢吸附自由能,并且更加有效地降低了氢释放势垒,从而优化了析氢反应动力学.综上,本文为元素掺杂工艺提供了新的思路,同时研究了表面异质原子对析氢活性的关键作用,为该类催化材料的构效关系研究提供了新思路.     

将铂(Ⅱ)-四(4-羧基苯基)卟啉组装到光捕获金属有机框架中增强可见光驱动的产氢效能

氢气析出反应的分子催化剂因能够将其整合到用于光催化水分解的光捕集复合物中而受到广泛关注.研究者期望通过构建吸光网络,提高分子催化剂的光催化产氢效能.本文报道了以[(TCPP)Pt^Ⅱ][TCPP=meso-四(4-羧基苯基)卟啉]络合物作为光催化产氢的分子催化剂.采用氯冉酸(CA)作为电子牺牲剂可以很好地稳定光催化剂,使CA被氧化为[CA-H·]自由基.当使用三乙醇胺作为电子牺牲剂时,[(TCPP)Pt^Ⅱ]分解形成Pt纳米颗粒.电化学循环伏安实验结果表明,光催化产氢的第一步是质子偶联电子转移,以获得[(TCPP)Pt+H]0.然而,第二个电子转移-1.02 V的氧化还原电位不随添加三氟乙酸而位移,表明该电子转移未与质子转移耦合,得到[(TCPP)Pt+H]-.此外,第二次电子转移的峰值处产生催化波,表明氢气是由[(TCPP)Pt+H]-的质子化生成,然后再生[(TCPP)Pt^Ⅱ]并释放氢气.密度泛函理论计算结果表明,[(TCPP)Pt^Ⅱ]分子催化剂光催化产氢的机理可能先经过质子耦合电子转移反应,形成[(TCPP)Pt^Ⅰ]-NH,然后依次经过电子注入和质子化形成[(TCPP)Pt^Ⅱ-H]-NH中间体,最终释放H2.由于整个催化循环过程涉及多个电子的注入,光捕获网络的引入有助于提供多个光电子.因此,本文通过将[(TCPP)Pt^Ⅱ]掺杂生长到主要由[(TCPP)Zn^Ⅱ]构筑的金属有机框架中,构筑了与分子催化剂连接的光捕获网络,从而将其活性提高了约830倍.纳秒瞬态吸收光谱和时间分辨的磷光光谱表明,向[(TCPP)Pt^Ⅱ]均相溶液中加入氯冉酸会因电荷转移而缩短3[(TCPP)Pt^Ⅱ]*寿命.同样现象在金属有机框架体系中也被观察到.然而,在磷光猝灭后,瞬态吸收光谱观察到均相溶液中[(TCPP)Pt+H]0及[CA-H·]自由基信号迅速衰减,在微秒时间尺度上衰减为0,表明大部分还原的[(TCPP)Pt+H]0迅速与氧化后的[CA-H·]复合,限制了光催化氢气析出的光量子效率.然而,在金属有机框架体系中,磷光猝灭后纳秒瞬态吸收光谱在较长时间尺度观察到残留吸收带,表明随后消耗CA,向反应体系中注入电子,推动了反应的完成.本文研究了能量转移对光催化H2析出的影响,并强调了光捕获网络在多电子注入中的重要性.     

过渡金属电催化剂在硅基光阳极分解水产氧中的作用

光电化学分解水可将太阳能转换为绿色的氢能,为目前的能源危机和环境问题提供了一种理想的解决方案.在分解水反应中,涉及四空穴过程的产氧半反应是制约性能的关键步骤,往往需要在半导体表面沉积电催化剂以加速产氧反应动力学.因此,全面理解电催化剂在光电化学分解水体系中的作用至关重要.在目前的产氧电催化剂中,过渡金属羟基氧化物电催化剂(MOOH,M=Fe,Co,Ni)因其环保、廉价、高效以及稳定的特性,已被广泛用于半导体光阳极分解水器件中.而且,MOOH可用简单的电沉积方法沉积在光电极表面,易于大面积制备.然而,电沉积法制备的MOOH具有复杂的结构,对其作用机制的全面理解更加困难.因此,本文以电沉积MOOH修饰的硅基光阳极(n⁺p-Si/SiO_x/Fe/FeOx/MOOH)作为模型,研究了不同电催化剂对硅光阳极光电化学产氧性能的影响.实验发现电催化剂的界面优化在电催化剂修饰的光电极中发挥着重要作用,这是因为优化的界面可以提升界面电荷传输,提供更多的催化反应活性位点以及更高的本征催化活性,从而更有利于光解水性能的提升.该项研究揭示了电催化剂在光解水器件中的作用,并为今后高效光解水器件的设计提供了一定指导.首先在多晶n⁺p-Si基底上热蒸镀了一层30 nm的金属Fe膜,并通过电化学活化将Fe膜表面转换为FeOx得到Fe/FeOx(记作aFe)界面层,然后利用电沉积方法制备MOOH表面修饰层,最终得到n⁺p-Si/SiO_x/aFe:MOOH光阳极.X射线光电子能谱、拉曼光谱以及扫描电子显微镜表面元素成像的表征结果均证实电极表面由于界面层金属Fe元素的掺杂而形成了Fe1-xNixOOH.在模拟太阳光下用于光解水产氧时,n⁺p-Si/SiO_x/aFe:NiOOH电极的起始电位为~1.01 VRHE(相对于可逆氢电极的电势),在1.23 VRHE下的光电流为38.82 mA cm^-2,显著优于n⁺p-Si/SiO_x/aFe、n⁺p-Si/SiO_x/aFe:FeOOH以及n⁺p-Si/SiO_x/aFe:CoOOH三个对比样品,且其稳定性达到75 h.另外,我们发现n⁺p-Si/SiO_x/aFe:MOOH电极的光电化学产氧性能均显著高于n⁺p-Si/SiO_x/aFe电极,且p++-Si/SiO_x/aFe:MOOH的电催化产氧性能也高于p++-Si/SiO_x/MOOH,不仅证明了aFe界面层对Si与MOOH层之间的界面接触作用的有效调控,而且表明双电催化剂体系(aFe:MOOH)的电催化产氧活性高于单电催化剂(MOOH).热力学分析表明,n⁺p-Si/SiO_x/aFe:MOOH光阳极的光电压大小与其光解水产氧性能并不一致,从而排除了热力学因素对性能的关键影响.进一步从塔菲尔斜率、电化学活性表面积和电化学阻抗谱对各电极的动力学进行了分析,证明了动力学因素在上述光阳极产氧性能中的主导作用.同时发现,由于aFe:NiOOH双电催化剂具有更高的本征电催化产氧性能,提供了更多的表面活性位点以及更有效地促进了光生载流子的传输,对动力学的提升效果更显著,从而使n⁺p-Si/SiO_x/aFe:NiOOH光阳极表现出最高的光解水产氧性能.